Selection of dust remover in Cupola
Product Description
Characteristics of cupola flue gas and selection of cupola dust collector in foundry plant:
The selection of the dust collector of the cupola is based on the large fluctuation range of the flue gas temperature, which mainly depends on the capacity of the furnace, the ratio of coke and iron, the height of the material and the unit air supply. In general, the temperature of the flue gas is about 100~200 degrees centigrade when there is no clear fire, and the temperature is generally 300~500 C when there are more iron chips and oxide skins in the molten iron or raw material. From the end of the feeding to the stop of the blast stage, as the material level drops and the fire rises, the temperature rises sharply, the fire is completely reburning at 200~900 degrees C; the fire is not completely reburning at 150~800; no further combustion is 100~600, and the blink of the blower is 900~1250 centigrade; the furnace is 600~800 centigrade; the capacity is large. In the cupola, the furnace gas contains more CO content, and the temperature can reach 800~1000 degrees centigrade when reburning, and the gas temperature of the pulverized coal cupola is always higher, generally 800~1000. According to the general situation of cupola flue gas, the cupola deduster adopts the following dust removal equipment to complete the purification of the cupola flue gas.
1. Cyclone dust collector is a primary and efficient cupola deduster. The dust removal efficiency can reach more than 70%, and the resistance of the dust collector is less than 800Pa. The dust remover can separate the particles from the large particles in the flue gas and the centrifugal force produced by the rotating airflow. The dust particles are separated from the dust flow, and the dust is discharged from the discharger. The purged flue gas is discharged into the two stage dust removal and cooling equipment of the cupola.
2. The structure and principle of the cooler: the cooler is made up of upper box, middle box and ash hopper. The flue gas of the cupola is set to a number of small pipes through the diameter of the main pipe. The section becomes larger, the Wind Speed slows down, and the wind blower is attached by the strong cold wind of the axial fan in order to reduce the temperature, and it also plays the role of settlement. The flue gas after cooling is drained into the cupola deduster through the pipeline.
3, cupola dust collector: in recent years, the application of bag filter in the fume cleaning system of the cupola has developed rapidly. The dust removal efficiency is more than 99%, and the dust emission concentration can be stabilized below 50mg/m3. The cleaning and cooling equipment before the bag filter (such as cyclone, cooler, etc.) can lighten the wear of bag filter.
When the filter material of cupola deduster is used as polyester filter material, the filtration speed is about 1.0m/min. For example, when using glass fiber filter material, the filtration speed is about 0.5m/min.
ZC mechanical rotary back blow flat bag filter
Its working principle, filtering conditions and dust laden gases enter the upper space of the filter chamber in tangential direction. The small particles of large particles and coagulated dust particles are dispersed along the clearance of the filter chamber bag, and the clean air is collected through the bag wall through the bag wall through the filter bag, which is absorbed by the ventilator and discharged into the atmosphere.
When the filter condition is carried out, the dust is attached to the surface of the bag, and the resistance of the filter bag is gradually increased. When the upper limit of the control resistance is reached, the Differential Pressure Transmitter of the interface connected to the wind pipe of the dust collector automatically starts the work of the anti blowing mechanism.
A sufficient amount of blow back air flow is blown into the filter bag by the rotary arm nozzle to blow back one by one. When the resistance of the filter bag falls to the lower limit, the anti blow mechanism stops working automatically.
The reverse blowing mechanism, in order to save the power of the air blower, reduce the back blowing and dust cleaning, is not restricted by the air source conditions in the use, easy to replace, easy to maintain, reliable in operation, to overcome the malady of the air pulsation in compressed air, to use a long filter bag, to make full use of space and small area. The mechanical rotary reverse blow flat bag filter is the best equipment for the cupola purification system.
Contact us if you need more details on Selection of Dust Remover in Cupola. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Cupola Dust Collector、Dust Collector for Sale. If these products fail to match your need, please contact us and we would like to provide relevant information.
The selection of the dust collector of the cupola is based on the large fluctuation range of the flue gas temperature, which mainly depends on the capacity of the furnace, the ratio of coke and iron, the height of the material and the unit air supply. In general, the temperature of the flue gas is about 100~200 degrees centigrade when there is no clear fire, and the temperature is generally 300~500 C when there are more iron chips and oxide skins in the molten iron or raw material. From the end of the feeding to the stop of the blast stage, as the material level drops and the fire rises, the temperature rises sharply, the fire is completely reburning at 200~900 degrees C; the fire is not completely reburning at 150~800; no further combustion is 100~600, and the blink of the blower is 900~1250 centigrade; the furnace is 600~800 centigrade; the capacity is large. In the cupola, the furnace gas contains more CO content, and the temperature can reach 800~1000 degrees centigrade when reburning, and the gas temperature of the pulverized coal cupola is always higher, generally 800~1000. According to the general situation of cupola flue gas, the cupola deduster adopts the following dust removal equipment to complete the purification of the cupola flue gas.
1. Cyclone dust collector is a primary and efficient cupola deduster. The dust removal efficiency can reach more than 70%, and the resistance of the dust collector is less than 800Pa. The dust remover can separate the particles from the large particles in the flue gas and the centrifugal force produced by the rotating airflow. The dust particles are separated from the dust flow, and the dust is discharged from the discharger. The purged flue gas is discharged into the two stage dust removal and cooling equipment of the cupola.
2. The structure and principle of the cooler: the cooler is made up of upper box, middle box and ash hopper. The flue gas of the cupola is set to a number of small pipes through the diameter of the main pipe. The section becomes larger, the Wind Speed slows down, and the wind blower is attached by the strong cold wind of the axial fan in order to reduce the temperature, and it also plays the role of settlement. The flue gas after cooling is drained into the cupola deduster through the pipeline.
3, cupola dust collector: in recent years, the application of bag filter in the fume cleaning system of the cupola has developed rapidly. The dust removal efficiency is more than 99%, and the dust emission concentration can be stabilized below 50mg/m3. The cleaning and cooling equipment before the bag filter (such as cyclone, cooler, etc.) can lighten the wear of bag filter.
When the filter material of cupola deduster is used as polyester filter material, the filtration speed is about 1.0m/min. For example, when using glass fiber filter material, the filtration speed is about 0.5m/min.
ZC mechanical rotary back blow flat bag filter
Its working principle, filtering conditions and dust laden gases enter the upper space of the filter chamber in tangential direction. The small particles of large particles and coagulated dust particles are dispersed along the clearance of the filter chamber bag, and the clean air is collected through the bag wall through the bag wall through the filter bag, which is absorbed by the ventilator and discharged into the atmosphere.
When the filter condition is carried out, the dust is attached to the surface of the bag, and the resistance of the filter bag is gradually increased. When the upper limit of the control resistance is reached, the Differential Pressure Transmitter of the interface connected to the wind pipe of the dust collector automatically starts the work of the anti blowing mechanism.
A sufficient amount of blow back air flow is blown into the filter bag by the rotary arm nozzle to blow back one by one. When the resistance of the filter bag falls to the lower limit, the anti blow mechanism stops working automatically.
The reverse blowing mechanism, in order to save the power of the air blower, reduce the back blowing and dust cleaning, is not restricted by the air source conditions in the use, easy to replace, easy to maintain, reliable in operation, to overcome the malady of the air pulsation in compressed air, to use a long filter bag, to make full use of space and small area. The mechanical rotary reverse blow flat bag filter is the best equipment for the cupola purification system.
Contact us if you need more details on Selection of Dust Remover in Cupola. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Cupola Dust Collector、Dust Collector for Sale. If these products fail to match your need, please contact us and we would like to provide relevant information.
Product Categories : Single Machine Dust Collector
Hot Products
Adblue level sensor for SCR systemFST800-211A OEM service offered 4-20mA Pressure Transducer transmitter for General IndustrialFST800-901 China manufacture of Differential Pressure Transmitter 4-20mAFST800-902 Micro Differential Pressure Transmitter for liquidFST800-211A Generator Oil Pressure Transmitter Sensor Pressure Transmitter for AutomobileFST700-201 Capacitance capacitive Oil Level Transmitter manufacturerFST200-201 Final supplier mechanical anemometer sensor with CEFST-RP Aluminum Shell Magnetostrictive Displacement Sensor , Magnetostrictive position SensorFST700-101 Input Liquid level transmitter , input type liquid level transmittersFST600-202 Integrated Temperature Sensor , Smart Integrated Temperature SensorFST800-211 4-20mA Universal Industrial Pressure TransmitterFST800-202 Universal General Industrial HP-Type Pressure SensorFST600-205 Explosion-isolated Temperature TransmitterFST600-101 Temperature Sensor Pt100 Pt1000FST200-201 With CE Wind speed sensor portable anemometer for wind turbineFST800-211 CE and RoHS approved Universal 4-20mA pressure transmitter